Blinker Genie (Formerly: Magic Blinker)

The Custom LED "Blinker Genie" is designed to allow single filament light bulbs, single intensity LED assemblies, or any two-wire indicators to function as both running lights AND blinkers - at full brightness!

Simply connect your two-wire incandescent or LED indicators  to the Custom LED Blinker Genie, and your indicator bulbs/LEDs will now stay on constantly as running lights, and blink when you engage the blinkers!  (Note: the indicator will turn off for the duration of the blinker pulse - this is how the blinking is achieved.)

The Custom LED Blinker Genie is designed to be as small as possible while being as versatile and robust as possible.  The finished dimensions of the unit will measure less than 0.7" x 1.25" X 0.25" and can carry up to 12A of current (see specifications)!  This ensures our product will work for any application (blinking your headlights individually, or powering one single LED signal for instance). 

To further ease installation and ensure dependability, the Custom LED Blinker Genies are entirely water resistant.

The Blinker Genie is applicable for any and all situations where a single filament lamp, or single brightness LED or LED cluster is desired to function as both a running light and a blinker light.

One Blinker Genie controls up to 2A worth of indicators on a single blinker circuit in the recommended configuration.  The Blinker Genies are sold IN PAIRS.  One will be required for each side of the motorcycle, for every 2A worth of switched indicator load (25W).

For most applications, they are used in the front to drive two wire LED indicators.  Technically, if you ran wires to the back, you could control the rear indicators with the Blinker Genies as well.  However, it is recommend that you use one Blinker Genie for each "corner" of the vehicle/motorcycle.

The Blinker Genies come with 7" leads, all required electrical connectors and detailed installation instructions!

For technical questions and product support, please E-mail support@customled.com.

• Made in the USA!
• New high-speed solid state design is compatible with all flasher relays.
• Built-in Stage I Load Equalizer eliminates the no-blink or 4-way blink condition.
• Comes as a complete kit with electrical connectors and detailed instructions.
• Works with LED or incandescent indicators.
• Completely water proof.
• Full 1 year warranty

Electrical Specifications:

• Maximum Recommended Indicator Load: 2A (30W)
• Maximum Switching Current: 12A
• Internal Resistance: 0.18 OHMS
• Maximum Switching Speed:  1Mhz
• Switch type: Advanced Power Mosfet
• ONLY functions with a Negative Ground System (most common)

Typical Installation Diagram

 

Installation Instructions

Installation of the Custom LED Magic Blinker is detailed in the instructions below.

click icon to download

 

Adobe Acrobat Reader is required to view this file.

If you are having problems viewing the file, please download the free software here.

For technical questions and product support, please E-mail support@customled.com.

 

GENERAL NOTE: For motorcycles that do not have running lights in the front of their motorcycle (such as the new Kawasaki sportbikes), the red wire on the Blinker Genie must be connected to an ignition switched source for proper operation.

HONDA BLINKER SYSTEM SPECIAL NOTE: In order to properly utilize the Custom LED Magic Blinkers on many Honda Motorcycles, the constant power input wire (red) must be connected to a ignition switched source (other than that for the front stock blinkers).  The little running light near the headlight is a perfect power source, OR you can connect the left and right running light wires together to create a constant running light source. 

The reason is because the running light wire that runs to the front signals cuts off completely when the blinkers are activated, and stays off until the blinkers are canceled.  This causes the operated load (LEDs or lamps)  to not work properly as the Magic Blinkers are designed to draw all power from the "running light" input wire.

Using a voltmeter, you can easily verify if you are having this problem.  Simply measure the voltage on the RED input wire on the Magic Blinker to check for constant 12V power - blinkers on AND off.

Custom LED consistently receives rave reviews from our customers about our products!  We try to post a representative group of them on our feedback page on this site, but we can't post them all! 

Our Feedback Profile on our Ebay Auctions are a great way to see what our customers think of our products, because Ebay promotes honest feedback.  Take a look at our Ebay Feedback!

Our commitment to quality, honesty, ingenuity and customer service is really making an impact in an industry full of careless "sell anything" retailers and hack-artist copy-cats.  Trust in our products, and see for yourself...